ĩ (3) Artnet software settings The artnet-receivers for udmx were tested with several softwares.
Art-Net network inferface with Linux: To create additional interfaces for Art-Net on Linux you just need a few steps: (1) install openvpn (2) Download below file, extract the contained files and copy them to the folder /etc/openvpn (3) Change the ip-addresses according to your needs Now you can list the new interfaces with ifconfig. (2) This new devices IP-address can be set independent from your other settings, thus can be set to 2.x.y.z or 10.x.y.z (3) At least on windows the program can read from OpenVPNs network device even if the device is not connectet, on the other hand you can connect the adapter. The installation of OpenVPN has several advantages: (1) OpenVPN creates a new interface (new network device).
So here you get an explanation how to find a solution for all difficulties with OpenVPN. IMPORTANT: The windows version of libpcap (Winpcap) does not support reading data from WLAN devices. Some programs allow setting the address to other values, but you should try setting the named adresses first. (3) Artnet You can get our ArtNet server(x-udmxartnet.exe) in the directory of "Artnet server\" Ĩ (2) Artnet network-configuration Documentation about Art-Net describes, that the IP-address has to be 2.x.y.z or 10.x.y.z.
Other operating systems or programs are available with the ArtNet server(we put the ArtNet server in the directory of "Artnet server\" in our compressed driver file. For your information, Under Linux you can use MagicQ of Chamsys or QLC. If you still want to use the old plugins, we put them in the directory of "plugins\" in our compressed driver file. We suggest to use udmx artnet if your DMX-software supports artnet, as udmx artnet makes it easy to setup DMX timing. X-uDMX512 Plugins: There are plugins for udmx from "ancient" times. The interface setup for FreeStyler is just choosing "udmx". (2) Plugin Newer versions of FreeStyler (>= 3.3.7) support X-uDMX512 directly. After udmx.dll has been copied to the directory of \system32\ for example: C:\WINDOWS\system32\, the driver installation is finished. Select the correct directory (of you uncompression), After several seconds the driver should be installed ATTENTION: And then the file udmx.dll has to be MANUALLY copied to the directory \System32\ in order to finish the installation. The operating system will search for a driver. Uncompress the file whereever you want and then plugin the hardware. X-uDMX512-2 shares the same driver with X- udmx DRIVER INSTALLATION: Download the compressed driver file (or find the driver directory in the CD- ROM). In case that you lost the driver files, you can download it via link. For X-uDMX512-2 for Macintosh, pls refer to the directory of \X-uDMX512 for Macintosh \ in the zipped file X-uDMX512_Driver.rar All files are in the CD-ROM in the packing box. Besides, on Unix-based operating systems, the LibUSB is integrated directly into the kernel. (8) L6.9cm(total 70cm with USB and 3-pin XLR connectors) x W4.1cm x H1.8cm ģ (1) Driver The driver for Windows XP, Vista and Windows 7.
(6) Drivers for Windows and Linux and Macintosh. This works for example with Magic Q, Abuelites or any other DMX-software that is able to output DMX-data to Art-Net. X-uDMX P can even be used with programs where there is no plugin. So it is not necesary to have a plugin for each program. (4) Supports Various 3rd party softwares (FreeStyler, DMXControl.PC-Dimmer, Q Light Control, Vixen, etc ) Besides, most DMX-Software are able to output DMX-data to Art-Net. (3) 1500 V full isolation(data & power lines to protect your computer from surges). 2 DMX Output Ports thru 3 pin XLR connectors (2) Micro processor enabled.